Software upgrade for the access control you already own ENEspañol中文For locksmithsFor integratorsSign in(281) 536-6272[email protected]
GateStride
Do it yourself

Install GateStride yourself, free for one door

If you are comfortable with a Raspberry Pi and a command line, you can run GateStride on your own hardware. Everything below is the same software our installers use. The free licence covers one door with no end date; contact us for more doors or for an installer near you.

GateStride works on top of your existing access control. It does not wire into a lock and does not replace your panel: it asks the panel to open the door, the way an operator would, so the panel keeps its fire, egress and audit behaviour. You need a supported system. Kantech EntraPass (with the SmartLink web service) is verified today; see integrations for the others.

What you need

For the buildingOne computer that stays on, on the same network as your access control: Windows 10/11 (x64), or Linux with systemd (x86_64 or arm64, e.g. a Raspberry Pi 4/5 or a mini PC). This runs gsmain.
For each doorRaspberry Pi 4/5 (2 GB+) with Raspberry Pi OS 64-bit, an ESP32-WROOM-32U board with a 2.4 GHz antenna, and an HLK-LD2450 24 GHz radar. This is a gsnode. Wire the radar to the ESP32: LD2450 TX → GPIO16, RX → GPIO17, 5V, GND. The ESP32 plugs into the Pi by USB.
PhonesAndroid 8 or later for GateStride Pass (staff) and GateSmith (you, for setup).
Access controlAn operator account in your access control system reserved for GateStride (one session, not shared with a person).

Downloads

FileForSHA-256
gsmain 2026.11.11, Windows x64
24.3 MB · signature
gsmainf074c35fd4abe0ec89be5f08dee83568508c4efc1fce84137292bb5f8e2d4357
gsmain 2026.11.11, Linux x86_64
21.8 MB · signature
gsmainbc59bd1c3cc1ed8b088fe7cd465743742e8c8d51dd160b03332061d212b88092
gsmain 2026.11.11, Linux arm64
18.3 MB · signature
gsmain04010156c0092b29dcc734822659517f404243699d6874cbe1a53e6f6189395d
gsnode 2026.10.25
119 KB · Raspberry Pi / Debian · signature
each dooreb4c18067ea1bd9b7c516a3f55d8105a0a79005936824f4895829b3202baa3aa
ESP32 door firmware
2.1 MB · version + signature
each doorf8c7e6ca02c894e37d5188e78493905fabbfde9bef533f4b9ab12ccd49428dbe
GateSmith 0.85 (Android)
125 MB · installer app
you204e2259cbb314aa02907ae3f976393288349edab2efaeba6c86b18237321ca1
GateStride Pass 1.21 (Android)
5.3 MB · staff app
staff67584a02a3d682525cee503ebc89ffe72f698313957287bd1ad3473f67a8538f

1. Install gsmain

Windows: unzip, then in PowerShell as Administrator:

powershell -ExecutionPolicy Bypass -File gsmain\install.ps1

Linux:

tar xzf gsmain-2026.11.11-linux-*.tar.gz && cd gsmain && sudo ./install.sh

It runs as a service that starts at boot. The installer prints a one-time password for the owner account: sign in at https://<that-computer>:8790/ and change it. gsmain carries its own Python; nothing else needs installing.

2. Register (free, one door)

In gsmain open Backup → Licence → Activate. It shows a link and a code: open the link on any device, sign in with Google, confirm. gsmain registers itself within seconds. No internet on that computer? Use Offline request and email the file to [email protected].

3. Connect your access control

In Underlying system, pick your system, enter its address and the operator account reserved for GateStride, then use Test. The health view shows each link (server, login, gateway, door) and, if one fails, whose equipment it is.

4. Build the door node

  1. Flash the ESP32 once from the Pi (afterwards the node keeps it updated by itself, with signed firmware):
    wget https://gatestride.com/download/firmware/esp32_node.bin
    sha256sum esp32_node.bin      # compare with the table above
    sudo apt install -y esptool
    python3 -m esptool --chip esp32 --port /dev/ttyUSB0 write_flash 0x0 esp32_node.bin
  2. Install gsnode:
    tar xzf gsnode-2026.10.25.tar.gz && cd gsnode && sudo ./install.sh
    On the same network it finds gsmain by itself. Elsewhere, create a Remote node claim code in gsmain (Door nodes) and run sudo ./install.sh --claim <code>.
  3. In gsmain → Door nodes, approve the new node and pick the door it opens. It takes its door identity and signed credentials from gsmain within seconds.

5. Calibrate and add people

Open GateSmith next to the door: it finds the node and walks you through the radar calibration (where the door line is, which side is inside). Then add people in gsmain and send each one an invite: they open it on their phone, GateStride Pass installs their badge, and the door opens as they walk up.

Check a download

Every installer has a .sig file: an Ed25519 signature by the GateStride release key over the file.

python3 - gsnode-2026.10.25.tar.gz <<'EOF'
import base64, sys
from cryptography.hazmat.primitives.serialization import load_pem_public_key
pub = load_pem_public_key(b"-----BEGIN PUBLIC KEY-----\nMCowBQYDK2VwAyEACeCbYu6fl67waUI68d/SW9HjeMSzp1Dng4MhfewYWGc=\n-----END PUBLIC KEY-----\n")
pub.verify(base64.b64decode(open(sys.argv[1] + ".sig").read()), open(sys.argv[1], "rb").read())
print("signature OK")
EOF

The Android apps are signed with their own keys: GateStride Pass certificate SHA-256 20b2f66e…608b, GateSmith 0338ed10…faa5. Android refuses an update signed by anyone else.

Self-installed GateStride is provided as is. You are responsible for using it with access control you are allowed to operate. Kantech, EntraPass and other names are trademarks of their owners; GateStride is independent and not affiliated with or endorsed by them.